How to blend paint and clear. How to Spray and Blend Automotive Clear Coat

You want to go past the sand through area with each pass but do not go all the way to your masking tape. Apply your base color in a feather spray pattern only covering the primed areas first. I can't stress enough on clearing the whole panel, Ask me how I know blends are difficult. Stop a couple of inches short of that and using your wrist you want to sweep the gun away from the surface. I was going text to a picture to Barry but the defect don't show on the cell phone so I will post here. After my normal sanding and buffing I could see a difference in color at the blend it looked a little like silver line at the blend line. This is on the lower rear quarter of a 57 Chevy ht.

 

Painting a quarter panel on some cars that don't have a break line is the classic reason why you need to know how to do this. You need to blend into the.They promised to fix it so I brought the car back and left it there.

 

Most of the time paint manufacturers will not warranty this type of repair. When there is a style line available, backmasking off of that line.And now he wants to help and teach you so you can customize, fix or restore any type of project you desire with professional auto body instruction and materials.

 

Schubert's Blending Clear is a resin modified basecoat blending clear for use in conjunction with 2K Basecoat System. It fills fine scratches caused by.Shop All Workshop Classes.

 

Using grit sand paper, wet scuff beyond the area to be blended so you have a section to melt your clear coat to. You can use a paint blender that you.In the garage it looked pretty good to my inexperienced decrepit eyes.

 

You can also blend the clear coat, which will result in a lower final product consumption. Clear coat blending is.On the first repair.

 

On the last coat is where you will mix your reducer with your clear. Mix the proper amount and blend only over the section where the clear is.Final bonus: clear coat blending.

 

Clear blends are difficult and will show lines unless you use This was my first attempt at blending paint so I was extremely nervous.You could carefully wetsand if the new clear is built up more than the old, but you might have a bigger problem to fix, as you might go through surrounding clear.

 

Spray an equal number of coats of clear coat on the area in the same manner as you applied the automotive paint. Leave the car to dry for up to two days. Step 7.Fortunately, body work and paint shop professionals use certain techniques, such as colour blendingto help minimise colour differences in the eyes of customers, obtaining optimum colour matching, integration and adjustment.

 

Buff with a clean cloth to a high gloss. (You may want to spray some paint and clearcoat on a smooth surface and practice to get the feel of it.) Sometimes lots.This is the process of blending new paint into the existing color to produce a color match.

 

Current automotive clear coats paints are irreversibly cured and therefore, the clear coat surrounding a spot repair cannot be “melted / blended.Factors causing body colour matching problems.

 

The most important part of blending single stage and clear is that the new paint be allowed to FULLY harden before it's polished.Do you have any photos of the job at hand?

 

After blending the paint, the entire panel will need to be clear coated. If the blend is close to an edge, blending and clearing into the adjacent panel may.On the last coat is where you will mix your reducer with your clear.

 

I like the comet and water or you can sand it with wet, you just need to scuff the clear coat. when you spray the base color spray one light.Remove the wet sandpaper from the water and rub across the surface you've just repainted in long, fluid strokes.

 

This makes your vehicle look gross (like a peeling sunburn), but paint shops will want to strip it all and repaint it, which takes weeks and.Masking is a very important step especially when blending because you need to blend into areas that will not be totally masked.

 

However, 3M recommends to use grit grit on a DA with an interface pad on adjacent panels to be clear coated.

 

Here is what one site said.

 

Imagine you are spraying an inside 90 degree corner and you have to turn your wrist to keep from loading the paint into the corner.

 

Step 7 Immerse 1,grit wet sandpaper in a bucket of water.

 

The time now is PM.

 

Depending on the size of the damage to be repaired and where it is located on the part, the blending technique can be classified into two different techniques:.

 

View attachment Cleared: View attachment Buffed: View attachment

 

Search forums.

 

Factors causing body colour matching problems.

 

By 15 he had painted his first car, and by 19 he ran his own successful auto body and paint shop.

 

Please wait while your request is being verified... forum? With looking at the picture can you guys tell if this defect is from poor blend or from not clearing the whole panel.

 

Gradually widen your coverage on the coats until your base coat starts to blend with the original base color on your panels.

 

In degraded areas where less paint is applied, these particles can be oriented or placed differently, which can lead to clouding or cloudiness.Forum How to blend paint and clear

 

Leave the paint to dry overnight.Forum How to blend paint and clear

 

New to this website?

 

More by the author:.

 

I mixed up a small amount of reduced clear to use as in "inter-coat.

 

Step 4 Apply the automotive paint to the area using a spray can, working the can back and forth across the area.

 

Remember your base coat will be sprayed on this inter-coat so give yourself some room to work.

 

I was going text to a picture to Barry but the defect don't show on the cell phone so I will post here.

 

After my normal sanding and buffing I could see a difference in color at the blend it looked a little like silver line at the blend line.

 

If it does cloud the old paint just buy some polish, something better than Turtle wax compound, many brands if you read a little on this site.

 

I can spray from top to bottom, but what about left to right, that whole bumper area will be sprayed to not have the line.

 

Over time, the original paint of a vehicle fades and oxidises.

 

Workshop Classes.

 

Similar Threads Can opti-coat stop clear coat failure?

 

A car dealer scratched the bumper on my car while performing a scheduled service.